HomeView CartRacing EventsSchool HolidaysRace ClubPartiesHire & InfoAbout UsSearchForumFreight InfoContact UsJoin Mailing ListTrade AccountHW Int'l


Product Categories
FUTURE RELEASES
LATEST ARRIVALS
SPECIALS
STOCK CLEARANCE
SlotCar Sets & Accessories
1/24 Slot Cars
1/24 Accessories
1/32 Slot Cars
1/32 Accessories
1/43 Slot Cars
1/64 Accessories

RC Vehicles
RC Parts & Accessories
Books and Catalogues
Die Cast & Model kits
Paints & Decorating
Track Building/Scenery
Trains
Workshop
AB SLOT SPORT
AFX
ALPHA
ARP GEARS
Biolink
BYCMO BIKES
CAHOZA
CAMEN
CARRERA
CATMARK REPLICAS
CHAMPION
COLT
DELTA AIRBRUSHING
DIFALCO CONTROLLERS
ESKY
GENERIC
FLYslot
HIMOTO
HOBBY PRO
HW INTERNATIONAL
INTEGY
IMPETUS RC
iWAVERS
JK PRODUCTS
KOFORD
KYOSHO
LANXIANG
MAGNATECH
MJK
MOSSETTI
MRS
MURA
NANDA RAPTOR
NINCO
NSR
PARMA/CHAMPION
PLAFIT
PRO SLOT
PRO TRACK
RAPIDFIX
REH
SCALEAUTO
SCALEXTRIC
SCX
SLICK 7
SLOT.IT
SMARTECH
SONIC
SPRINTS PLUS
TAMIYA
TQ PRODUCTS
TRAXXAS
ULTIMATE
VS TANKS
WRIGHT WAY

Current Category
DIFALCO CONTROLLERS > DIFALCO INFO


LogoDifalco.gif

Difalco Design

NEW GENESIS CONTROLLER DESIGN.

 

The new Genesis controllers will replace some of the current controller line. We still have Pro Plus, Fanatic and HD30 controller models but the layout has been updated with exciting new features.

 

Design change overview: All Genesis controllers now feature a cable type design. The heatsink has been moved from under the handle to the track panel and results in a lightweight handle design with a flexible cable from the handle to the heatsink unit. All Genesis controllers also feature a new brake and transistor fuse for enhanced reliability. These controllers are positive polarity only and can not be switched to negative polarity.

 

Remember! All Difalco controllers feature a ball bearing trigger for lighter trigger response.

 

GENESIS FANATIC 1/24 CONTROLLERS

All Genesis Fanatic controllers feature the new layout with a Hybrid cable between the handle and the heat sink. This hybrid cable consists of 2) 14 ga. wires for the brake circuit and 3 very small wires to activate the electronics. This gives a very light controller with a super flexible cable. All Fanatic controllers come with a Blast full power relay and 10 ga wires from the heat sink unit to the track.

DD268: The most versatile controller, especially if you race multiple scales or wing cars! Installed with 20 ohm Fanatic pots this controller can run any car from home set 1/32, H.O. up to the fastest G7 motors by adjusting the Fanatic pots with a twist of a screwdriver. This model features an economy brake rheostat and Blast relay.

GENESIS HD30 CONTROLLERS

All Genesis HD30 controllers feature a single multiconductor cable design between the handle and the heat sink. All HD30 controllers also come with a Blast full power relay and 10 ga. wires from the heat sink to the track. All HD30 models come standard with a 148 ohm HD30 network (medium response) installed which is best suited for 16d and G12 motors. Optional networks available.

*****INCREDIBLE NEW FEATURE ON ALL GENESIS HD30 CONTROLLERS*****

Extreme Stopping Power brake relay

The new E.S.P. brake relay significantly improves full brake response for scale and retro type racing. The brake relay is controlled by a tiny switch on our circuit board. When activated the heat sink mounted relay bypasses the brake rheostat and the fuse to give the shortest resistance path and maximum braking. Since the relay does not depend on contact between the trigger and the brass brake post the braking response will not degrade because of arcing built up on the contact surfaces. This means perfect and consistent braking every time.

DD271: 30 band controller with upgraded Pro brake rheostat. Optional plug in networks available. E.S.P. brake and Blast relay.

HD30 RESISTOR NETWORKS

Miniature plug in circuit board allows racer to change the overall band resistance to best suit the type of motor being used. The higher the listed ohms the slower the band response and the lower the listed ohms the faster the band response. Standard networks are soldered and ready to install and have the same value resistance per band. Custom networks have miniature sockets and various values of resistors that can be mixed and matched to get the desired response. All controllers and modules come standard with a 148 ohm network. (As a comparison our 15 band Fanatic controllers have 150 ohms of total resistance).

(Note: the network resistance shown, 180 ohms for example, is the resistance needed to control our transistor circuit and should not be confused with the ohms rating on a typical Parma type resistor)

 

DD255: Standard Resistor Network. 180 ohm, slower response for flat track scale racing.

DD256: Standard Resistor Network. 113 ohm, faster response for 16d, G12, G15 and G20 motors.

DD257: Standard Resistor Network. 78 ohm, very fast response for G15, G20, G27 and G7 type motors.

DD258: Custom Resistor Network. Slow response. 33 each of 3 different value resistances let you customize response for scale racing. 136,162 and 192 ohms of total resistance if the same value is used per band. You can also mix and match resistors to best suit your track and driving style.

DD259: Custom Resistor Network. Faster response. 33 each of 3 different value resistances let you customize response for higher speed tracks and motors. 87,113 and 136 ohms of total resistance if the same value is used per band or you can mix and match response to best suit your track and driving style.

DD260: Custom Resistor Network. Very Fast response. 33 each of 3 different value resistances for customized response for high power G15,G20, G27 and G7 motors. 64,87 and 113 ohms of total resistance if the same value is used per band. You can also mix and match to best suit your track and driving style.

DD262: Standard resistor network. 290 ohms for H.O. and 1/32 homeset racing.

DD263: Standard resistor network. 218 ohms for faster response for H.O. and 1/32 homeset racing.

DD264: Custom Resistor Network. (West Coast Network) has specially selected resistors for scale and Retro cars.

DD720 Ball Bearing Upgrade Kit: Ball bearings, spacers and shims needed to correctly install ball bearings in a Difalco controller or module conversion already using our DD719 trigger Pin. Very easy to install.

 


 

Click here to go back to Home Page